The Features

Micron calls its enterprise feature set eXtended Performance and Enchanced Reliability Technology or just XPERT. It's a combination of hardware and software-level features that help to extend endurance and ensure data integrity at any time. Some elements of XPERT are present in client drives as well while some are limited to Micron's enterprise SSDs.


ARM/OR, short for Advanced Read Management/Optimized Read, is Micron's adaptive DSP technology (i.e. aDSP). The idea behind ARM/OR and aDSP in general is to monitor the NAND voltages in real time and make changes if necessary.

As NAND wears out, electrons get trapped inside the silicon oxide and floating gate. This changes the voltage required to read/program the cell (as the graph above shows) and eventually the cell would reach a point where it cannot be read/programmed using the original voltage. With ARM/OR the controller can adapt to the changes in read/program voltages and can continue to operate even after significant wear.


We've talked about RAIN (Redundant Array of Independent NAND) before as it is a feature Micron utilizes in all of its SSDs but I'll go through it briefly here. Essentially RAIN is a RAID 5 like structure that uses parity to protect against data loss. In the case of the M500DC, the stripe ratio is 11:1 for the 120GB, 240GB and 480GB models and 15:1 for the 800GB one, meaning that one page/block is reserved for parity for every 11 or 15 pages/blocks. The parity can then be used to recover data in case there is a block failure or the data gets corrupted.


DataSAFE ensures that all data, read or written, is intact. When writing data, Micron not only writes the data from the host to the NAND but also the metadata associated with the data (i.e. its logical block address/LBA). When the host then requests the data to be read from the drive, the LBA of the data is first compared against the value in the L2P table (logical to physical -- Micron's name for the NAND mapping table) before sending the data to the host. This ensures that the data that is being read from the NAND is in fact the same data that the host requested. If the LBA values of the NAND and L2P table are different, then the drive will have to rely on ECC or RAIN to recover the correct data.

In addition to LBA embedding and read checking, DataSAFE does data path protection from the SATA transport all the way to the NAND controller. While client drives only generate CRC and BCH error correction codes to detect errors, the enterprise drives add an additional memory correction ECC (MPECC) layer. MPECC is a 12-byte error-correcting code that follows the user data during its whole path. The difference between the client and enterprise solutions is that the client drives rely on the host to make the actual error correcting, whereas the MPECC layer can correct a single-bit error within the data path (i.e. before the data even hits the host).

Power Loss Protection

While both Micron's client and enterprise SSDs feature power loss protection, there is a difference between them. The enterprise drives features more rigid tantalum capacitors that provide a higher capacitance compared to the standard capacitors used in the client drives. The higher capacitance ensures that absolutely no data is lost during a power loss, whereas there is still a small risk of data loss in client drives. I believe the difference is that the capacitors in client drives only provide enough capacitance to flush the NAND mapping table (or L2P table as Micron calls it) to the NAND, while the enterprise solution guarantees that in addition to the NAND mapping table, all write requests in process will also be completed.

Introduction, The Drives & The Test Endurance Ratings: How They Are Calculated
Comments Locked


View All Comments

  • apudapus - Tuesday, April 22, 2014 - link

    I don't quite understand your statement in the first part:
    data retention decreases with NAND wear -> consumer drives have higher endurance

    Regarding the last sentence, SSD endurance is measured in number of writes like TBW. NAND endurance is measured in P/E cycles. The endurance of an SSD should not be measured in P/E cycles because erasing is handled internally to the SSD, there is no "erase" command to send to an SSD (trim does not directly yield an erase), write amplification (decreases endurance) and overprovisioning (increases endurance) must be taken into account and is not controlled by the user. Total writes is all that is needed when discussing SSD endurance. With that said, please explain your reasoning for the drive having a higher endurance than 3000 "P/E cycles".
  • Solid State Brain - Tuesday, April 22, 2014 - link

    The more P/E cycles your NAND memory goes through, the shorter its data retention time gets.
    Therefore, the shorter the data retention requirement for the intended usage is, the more P/E cycles you can make your memory can go through (or in other words: the more data you can write). Actually it's a bit more complex than that (for example the uncorrectable bit error rate also goes up with wear), but that's pretty much it.
  • apudapus - Wednesday, April 23, 2014 - link

    I see. So the assumption is that NAND with shorter data retention requires more refreshing (a.k.a. wasted programs). I believe this to be true for enterprise drives but I would be surprised to see this being done on consumer drives (maybe for TLC, though).
  • valnar - Tuesday, April 22, 2014 - link

    I wish they would find a way to lower the cost of SLC. Look at those endurance numbers.
  • hojnikb - Tuesday, April 22, 2014 - link

    Why would you want SLC anyway ?
    If you need endurance, HE-MLC is plety enough.
    Unless you write like crazy; them probobly buying SLC shouldn't pose a problem :)
  • valnar - Tuesday, April 22, 2014 - link

    Because 20nm TLC and crap like that barely holds a "charge", so to speak, when not powered up. That's just way too volatile for my liking. I'm not always running all my PC's every day.
  • bji - Tuesday, April 22, 2014 - link

    What difference does it make if the drive is powered up or not? These are static cells, they are not "refreshed" like DRAM. They are only refreshed when they are rewritten, and if your drive is not doing continuous writes, it's not guaranteed to rewrite any particular cell within any specific timeframe.
  • apudapus - Tuesday, April 22, 2014 - link

    NAND has limited data retention and should be refreshed like DRAM, albeit at a much larger timescale like 1 month (TLC) to a year (I believe 54nm SLC from years ago had this spec near the end of its life, ~100,000 P/E cycles). Good SSDs should be doing this.
  • Kristian Vättö - Wednesday, April 23, 2014 - link

    ALL consumer drives have a minimum data retention of one year, regardless of the type of NAND (SLC, MLC or TLC). This is a standard set by JEDEC. For enterprise drives it's three months.
  • apudapus - Wednesday, April 23, 2014 - link

    That may be the requirement for drives but not for NAND. Drives can do several things to increase data retention: refresh stale data after time, provide strong ECC, do voltage thresholding, etc. I think JEDEC specifies hundreds of hours for NAND retention.

Log in

Don't have an account? Sign up now